Search results

Sold!

$2100 shipped obo I no longer need this lower as I’m now running a 300x. This Sportmaster was on my 200xs which blew a powerhead. Please PM or call me at 916 995 6748 with any questions. https://imgur.com/gallery/gpQnj Neil

7/10 - $500 shipped This prop ran 87 gps on the limiter on my XB2003/200xs. I longer need this prop as I now run a 300xs. Call or text with any questions 916 995 6748 Neil https://imgur.com/gallery/J3PFS

http://www.bbcboards.net/showthread.php?t=802647

My 2002 200xs just lost cylinder 5 at 499hrs.

26P Hydromotive Quad IV X-OT w/extra Tip Cup I needed a fishing prop to run in the Delta. My 26P & 28P Quad IV OTs with outboard cut were taking a beating with all the debris in the water. Thought about getting a Promax prop but that would be a gamble. I knew if I got a prop from Todd...

http://rapidgator.net/file/8c50cf9f24c17d5a4bc5a39a1602309d/Allision_redbook.pdf.html

What kind of top speed numbers will a stock 26 Chopper II run on a XB2003 w/a 225 or 200? Thanks!

I just bought this prop and it ran 87 gps on my boat (Allison XB2003/200xs). It is time to update my gauges. $465 plus shipping firm (no trades) The prop ran 90 gps on the previous owners XB2003 w/225 promax.

Anyone know the cheapest place to get a replacement? They retail around $1200 and the cheapest I could find online was around $900 from ishopmarine.com. My air compressor brackets broke when I was going about 80 and the engine just cut out. Check out this picture:

I just received it from Sanderson's Marine today.

How safe is it for me to raise my limiter on my 200xs? I just don't want to go BOOM! He is charging $750 to raise the limiter and lighten the flywheel. Here is the link I was looking at: http://www.simonmotorsports.com/page3.html Thanks for looking...

I've been reading that some people have lost top speed with the foil on and some have not. -What prop(s) were people running who have lost top speed with the foil on? -What props were people running with no lost of top speed with the foil on?

Has anyone run the both of them together? If so, was there anything negative? I'm trying to decide if I should remove it or leave it on as I just installed the Ally skid plate. Thanks

http://forums.screamandfly.com/forums/showthread.php?t=141367

I made a video of my Ally on the River. Check it out here if you have sometime: http://www.youtube.com/watch?v=OInztCPFKAA

What could cause my 200xs to stall in gear? It will run for like 15 seconds without pushing on the gas pedal. After about 15 seconds the engine will start to bog and run really rough and finally die. It smells as if the engine is flooding. But if I give the engine a little gas to keep it going...

What could cause my 200xs to stall in gear? It will run for like 15 seconds without pushing on the gas pedal. After about 15 seconds the engine will start to bog and run really rough and finally die. It smells as if the engine is flooding. But if I give the engine a little gas to keep it...

Anyone ever replace there Sportmaster propshaft seals? If so, how involved is the work? Is this a DIY project if I order the correct tools like the bearing carrier wrench (91-61069)? Thanks in Advance, Neil

You can add me to the list. The engine spit, sputtered, and then it died for good. It left me stranded in the middle of the ca. delta. I haven't looked at it yet because I'm so pissed off. Hopefully, it isn't anything 2 serious.